View IRFS4321TRLPBF_6524214.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

12/9/10 www.irf.com 1 hexfet power mosfet benefits low r dson reduces losses low gate charge improves the switching performance improved diode recovery improves switching & emi performance 30v gate voltage rating improves robustness fully characterized avalanche soa applications motion control applications high efficiency synchronous rectification in smps uninterruptible power supply hard switched and high frequency circuits s d g gds gate drain source d 2 pak irfs4321pbf to-262 irfsl4321pbf s d g d s d g d irfs4321pbf irfsl4321pbf * r jc (end of life) for d 2 pak and to-262 = 0.65c/w. this is the maximum measured value after 1000 temperature cycles from -55 to 150c and is accounted for by the physical wearout of the die attach medium. notes through are on page 2 v dss 150v r ds(on) typ. 12m max. 15m i d 85a absolute maximum ratings symbol parameter units i d @ t c = 25c continuous drain current, v gs @ 10v a i d @ t c = 100c continuous drain current, v gs @ 10v i dm pulsed drain current p d @t c = 25c maximum power dissipation w linear derating factor w/c v gs gate-to-source voltage v e as (thermally limited) single pulse avalanche energy mj t j operating junction and c t stg storage temperature range soldering temperature, for 10 seconds (1.6mm from case) thermal resistance parameter typ. max. units r jc junction-to-case ??? 0.43* c/w r ja junction-to-ambient ??? 40 -55 to + 175 2.3 300 30 120 350 max. 85 60 330

2 www.irf.com s d g calculated continuous current based on maximum allowable junction temperature. package limitation current is 75a repetitive rating; pulse width limited by max. junction temperature. limited by t jmax , starting t j = 25c, l = 0.096mh r g = 25 , i as = 50a, v gs =10v. part not recommended for use above this value. pulse width 400 s; duty cycle 2%.

static @ t j = 25c (unless otherwise specified) symbol parameter min. typ. max. units v (br)dss drain-to-source breakdown voltage 150 ??? ??? v v (br)dss / t j breakdown voltage temp. coefficient ??? 150 ??? mv/c r ds(on) static drain-to-source on-resistance ??? 12 15 m v gs(th) gate threshold voltage 3.0 ??? 5.0 v i dss drain-to-source leakage current ??? ??? 20 a ??? ??? 1.0 ma i gss gate-to-source forward leakage ??? ??? 100 na gate-to-source reverse leakage ??? ??? -100 r g(int) internal gate resistance ??? 0.8 ??? dynamic @ t j = 25c (unless otherwise specified) symbol parameter min. typ. max. units gfs forward transconductance 130 ??? ??? s q g total gate charge ??? 71 110 nc q gs gate-to-source charge ??? 24 ??? q gd gate-to-drain ("miller") charge ??? 21 ??? t d(on) turn-on delay time ??? 18 ??? ns t r rise time ??? 60 ??? t d(off) turn-off delay time ??? 25 ??? t f fall time ??? 35 ??? c iss input capacitance ??? 4460 ??? pf c oss output capacitance ??? 390 ??? c rss reverse transfer capacitance ??? 82 ??? diode characteristics symbol parameter min. typ. max. units i s continuous source current ??? ??? 85 a (body diode) i sm pulsed source current ??? ??? 330 a (body diode) v sd diode forward voltage ??? ??? 1.3 v t rr reverse recovery time ??? 89 130 ns i d = 50a q rr reverse recovery charge ??? 300 450 nc v r = 128v, i rrm reverse recovery current ??? 6.5 ??? a di/dt = 100a/ s t on forward turn-on time intrinsic turn-on time is negligible (turn-on is dominated by ls+ld) v gs = 10v v dd = 98v t j = 25c, i s = 50a, v gs = 0v integral reverse p-n junction diode. showing the i d = 50a r g = 2.5 conditions v gs = 0v, i d = 250 a reference to 25c, i d = 1ma v gs = 10v, i d = 33a v ds = v gs , i d = 250 a v ds = 150v, v gs = 0v v ds = 150v, v gs = 0v, t j = 125c mosfet symbol v ds = 75v conditions v gs = 10v v gs = 0v v ds = 50v ? = 1.0mhz conditions v ds = 25v, i d = 50a i d = 50a v gs = 20v v gs = -20v

www.irf.com 3 fig 1. typical output characteristics fig 3. typical transfer characteristics fig 4. normalized on-resistance vs. temperature fig 2. typical output characteristics fig 6. typical gate charge vs. gate-to-source voltage fig 5. typical capacitance vs. drain-to-source voltage 3.0 4.0 5.0 6.0 7.0 8.0 9.0 v gs , gate-to-source voltage (v) 0.1 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( ) v ds = 25v 60 s pulse width t j = 25c t j = 175c -60 -40 -20 0 20 40 60 80 100 120 140 160 180 t j , junction temperature (c) 0.5 1.0 1.5 2.0 2.5 3.0 3.5 r d s ( o n ) , d r a i n - t o - s o u r c e o n r e s i s t a n c e ( n o r m a l i z e d ) i d = 50a v gs = 10v 1 10 100 v ds , drain-to-source voltage (v) 0 1000 2000 3000 4000 5000 6000 7000 c , c a p a c i t a n c e ( p f ) coss crss ciss v gs = 0v, f = 1 mhz c iss = c gs + c gd , c ds shorted c rss = c gd c oss = c ds + c gd 0 20406080100120 q g total gate charge (nc) 0 4 8 12 16 20 v g s , g a t e - t o - s o u r c e v o l t a g e ( v ) v ds = 120v vds= 75v vds= 30v i d = 50a 0.1 1 10 100 v ds , drain-to-source voltage (v) 0.1 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) 60 s pulse width tj = 25c 5.0v vgs top 15v 10v 8.0v 7.0v 6.5v 6.0v 5.5v bottom 5.0v 0.1 1 10 100 v ds , drain-to-source voltage (v) 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) 60 s pulse width tj = 175c 5.0v vgs top 15v 10v 8.0v 7.0v 6.5v 6.0v 5.5v bottom 5.0v

4 www.irf.com fig 8. maximum safe operating area fig 10. drain-to-source breakdown voltage fig 7. typical source-drain diode forward voltage fig 11. typical c oss stored energy fig 9. maximum drain current vs. case temperature fig 12. maximum avalanche energy vs. draincurrent 0.20.40.60.81.01.21.4 v sd , source-to-drain voltage (v) 0.1 1 10 100 1000 i s d , r e v e r s e d r a i n c u r r e n t ( a ) t j = 25c t j = 175c v gs = 0v -60 -40 -20 0 20 40 60 80 100 120 140 160 180 t j , junction temperature (c) 140 150 160 170 180 190 v ( b r ) d s s , d r a i n - t o - s o u r c e b r e a k d o w n v o l t a g e 0 20 40 60 80 100 120 140 160 v ds, drain-to-source voltage (v) 0.0 1.0 2.0 3.0 4.0 5.0 e n e r g y ( j ) 25 50 75 100 125 150 175 starting t j , junction temperature (c) 0 100 200 300 400 500 e a s , s i n g l e p u l s e a v a l a n c h e e n e r g y ( m j ) i d top 13a 20a bottom 50a 1 10 100 1000 v ds , drain-tosource voltage (v) 0.1 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) tc = 25c tj = 175c single pulse 1msec 10msec operation in this area limited by r ds (on) 100 sec dc 25 50 75 100 125 150 175 t c , case temperature (c) 0 10 20 30 40 50 60 70 80 90 i d , d r a i n c u r r e n t ( a ) limited by package

www.irf.com 5 fig 13. maximum effective transient thermal impedance, junction-to-case fig 14. typical avalanche current vs.pulsewidth fig 15. maximum avalanche energy vs. temperature notes on repetitive avalanche curves , figures 14, 15: (for further info, see an-1005 at www.irf.com) 1. avalanche failures assumption: purely a thermal phenomenon and failure occurs at a temperature far in excess of t jmax . this is validated for every part type. 2. safe operation in avalanche is allowed as long ast jmax is not exceeded. 3. equation below based on circuit and waveforms shown in figures 16a, 16b. 4. p d (ave) = average power dissipation per single avalanche pulse. 5. bv = rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. i av = allowable avalanche current. 7. t = allowable rise in junction temperature, not to exceed t jmax (assumed as 25c in figure 14, 15). t av = average time in avalanche. d = duty cycle in avalanche = t av f z thjc (d, t av ) = transient thermal resistance, see figures 13) p d (ave) = 1/2 ( 1.3bvi av ) = t/ z thjc i av = 2 t/ [1.3bvz th ] e as (ar) = p d (ave) t av 1e-006 1e-005 0.0001 0.001 0.01 0.1 t 1 , rectangular pulse duration (sec) 0.001 0.01 0.1 1 t h e r m a l r e s p o n s e ( z t h j c ) 0.20 0.10 d = 0.50 0.02 0.01 0.05 single pulse ( thermal response ) notes: 1. duty factor d = t1/t2 2. peak tj = p dm x zthjc + tc ri (c/w) ? (sec) 0.085239 0.000052 0.18817 0.00098 0.176912 0.008365 j j 1 1 2 2 3 3 r 1 r 1 r 2 r 2 r 3 r 3 c ci= i / ri ci= i / ri 1.0e-06 1.0e-05 1.0e-04 1.0e-03 1.0e-02 1.0e-01 tav (sec) 0.1 1 10 100 a v a l a n c h e c u r r e n t ( a ) 0.05 duty cycle = single pulse 0.10 allowed avalanche current vs avalanche pulsewidth, tav, assuming ? j = 25c and tstart = 150c. 0.01 allowed avalanche current vs avalanche pulsewidth, tav, assuming tj = 150c and tstart =25c (single pulse) 25 50 75 100 125 150 175 starting t j , junction temperature (c) 0 20 40 60 80 100 120 e a r , a v a l a n c h e e n e r g y ( m j ) top single pulse bottom 1% duty cycle i d = 50a

6 www.irf.com fig 16. threshold voltage vs. temperature !
! -75 -50 -25 0 25 50 75 100 125 150 175 t j , temperature ( c ) 1.0 2.0 3.0 4.0 5.0 6.0 v g s ( t h ) , g a t e t h r e s h o l d v o l t a g e ( v ) i d = 1.0a i d = 1.0ma i d = 250 a 100 200 300 400 500 600 700 800 900 1000 di f / dt - (a / s) 0 10 20 30 40 i r r m - ( a ) i f = 33a v r = 128v t j = 125c t j = 25c 100 200 300 400 500 600 700 800 900 1000 di f / dt - (a / s) 0 10 20 30 40 i r r m - ( a ) i f = 50a v r = 128v t j = 125c t j = 25c 100 200 300 400 500 600 700 800 900 1000 di f / dt - (a / s) 0 400 800 1200 1600 2000 2400 2800 3200 q r r - ( n c ) i f = 33a v r = 128v t j = 125c t j = 25c 100 200 300 400 500 600 700 800 900 1000 di f / dt - (a / s) 0 400 800 1200 1600 2000 2400 2800 3200 q r r - ( n c ) i f = 50a v r = 128v t j = 125c t j = 25c

www.irf.com 7 fig 23a. switching time test circuit fig 23b. switching time waveforms v gs v ds 90% 10% t d(on) t d(off) t r t f v gs pulse width < 1 s duty factor < 0.1% v dd v ds l d d.u.t + - fig 22b. unclamped inductive waveforms fig 22a. unclamped inductive test circuit t p v (br)dss i as r g i as 0.01 t p d.u.t l v ds + - v dd driver a 15v 20v v gs fig 24a. gate charge test circuit fig 24b. gate charge waveform vds vgs id vgs(th) qgs1 qgs2 qgd qgodr fig 21. " for n-channel hexfet power mosfets
?
? ?

p.w. period di/dt diode recovery dv/dt ripple 5% body diode forward drop re-applied voltage reverse recovery current body diode forward current v gs =10v v dd i sd driver gate drive d.u.t. i sd waveform d.u.t. v ds waveform inductor curent d = p. w . period #
# + - + + + - - - ? ! ? "#$## ? % && ? #$##'$

1k vcc dut 0 l

8 www.irf.com

f 530s this is an irf530s with lot code 8024 as s embled on ww 02, 2000 in the assembly line "l" assembly lot code int ernational rectifier logo part number dat e code year 0 = 2000 week 02 line l
(dimensions are shown in millimeters (inches)) dat e code in the assembly line "l" as s embled on ww 02, 2000 this is an irf530s with lot code 8024 int ernational logo rectifier lot code part number f 530s for gb production

www.irf.com 9 to-262 part marking infor logo rect ifier international lot code as s e mb l y logo rect ifier international dat e code we e k 19 ye ar 7 = 1997 part number a = as s e mb l y s i t e code or product (optional) p = de s i gnat e s l e ad- f r e e example: this is an irl3103l lot code 1789 as s e mb l y part number dat e code week 19 line c lot code ye ar 7 = 1997 as s embled on ww 19, 1997 in the assembly line "c" to-262 package outline (dimensions are shown in millimeters (inches))

10 www.irf.com data and specifications subject to change without notice. this product has been designed and qualified for the industrial market. qualification standards can be found on ir?s web site. ir world headquarters: 233 kansas st., el segundo, california 90245, usa tel: (310) 252-7105 tac fax: (310) 252-7903 visit us at www.irf.com for sales contact information . 12/2010
3 4 4 trr feed direction 1.85 (.073) 1.65 (.065) 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) trl feed direction 10.90 (.429) 10.70 (.421) 16.10 (.634) 15.90 (.626) 1.75 (.069) 1.25 (.049) 11.60 (.457) 11.40 (.449) 15.42 (.609) 15.22 (.601) 4.72 (.136) 4.52 (.178) 24.30 (.957) 23.90 (.941) 0.368 (.0145) 0.342 (.0135) 1.60 (.063) 1.50 (.059) 13.50 (.532) 12.80 (.504) 330.00 (14.173) max. 27.40 (1.079) 23.90 (.941) 60.00 (2.362) min. 30.40 (1.197) max. 26.40 (1.039) 24.40 (.961) notes : 1. comforms to eia-418. 2. controlling dimension: millimeter. 3. dimension measured @ hub. 4. includes flange distortion @ outer edge.

▲Up To Search▲

Price & Availability of IRFS4321TRLPBF

	To Download IRFS4321TRLPBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .